Winlink Wednesday: Send Winlink over HF with VARA HF + This Week’s Challenge

So far on Winlink Wednesday we’ve sent messages over the internet, over VHF with VARA FM, with ICS-213 forms and peer-to-peer. The catch with VHF is range: if there’s no gateway nearby, you’re stuck. HF fixes that. With VARA HF and an HF radio, you can reach a Winlink gateway hundreds of miles away, which is exactly what you want when the local infrastructure is down.

Level: Intermediate | Time: about 45 minutes the first time | Note: Winlink Express and VARA both update often, so a label or two may look a little different on your screen. The free VARA HF works but is slower; a paid registration key from the VARA developer unlocks the full speed.

Four steps for Winlink over HF: install VARA HF, open a Vara HF Winlink session, set up the TNC, radio and sound card, then pick a gateway, listen and connect
Four steps from VHF-only to HF reach.
Prefer to watch? Here’s the 4-minute video.

What You’ll Need

  • An HF radio connected to your computer for audio and rig control, either with built-in USB (like the IC-7300 or FT-991A) or through an interface like the Digirig Mobile
  • An HF antenna for the band you’ll use, such as a dipole for 40 or 20 meters
  • Winlink Express (already set up from our first Winlink Wednesday) and VARA HF, both free downloads for Windows

Step 1: Install VARA HF

Download VARA HF from the developer’s site (rosmodem.wordpress.com) and install it. It’s a separate program from the VARA FM you installed a few weeks ago. Winlink Express finds it on its own once it’s installed.

Step 2: Open a VARA HF Session

In Winlink Express, pick Vara HF Winlink from the session drop-down (make sure it’s HF, not FM) and click Open Session. If it asks to update propagation data, say yes. That helps it guess which gateways you can reach.

Step 3: Check the TNC and Radio Settings

  • In the session window, open Settings → VARA TNC Setup. The defaults (host 127.0.0.1, port 8300) are usually right. Leave the bandwidth at the default 2300 to start, and check the box to launch VARA automatically when the session opens. Click Update.
  • Open Settings → Radio Setup. Pick your radio model, choose USB Digital, and select the COM port and baud rate your radio uses for CAT. Icom owners also enter the CI-V address (the IC-7300’s default is 94). Click Update.

Step 4: Set Up VARA’s Sound Card

In the VARA HF window, open Settings → SoundCard. Pick your radio’s USB audio device (or your interface) for both input and output. If the VU meter in VARA moves when you hear band noise, the computer is hearing the radio. Then adjust the Drive Level so you reach your power without pushing the ALC hard. Guides differ on the exact ALC reading, so follow your radio’s manual for digital modes and stay on the low side.

Step 5: Pick a Gateway

Click Channel Selection in the session window, then Update Via Internet to grab the latest gateway list and predictions. Sort by the Path Reliability estimate so the stations you’re most likely to reach float to the top, and pick one on a band your antenna can handle. Its call sign and frequency fill into the session window, and your radio should tune itself there.

Step 6: Listen, Then Connect

Make sure your radio is in its data mode (USB-D, DATA-U or similar) with a wide enough filter. Write a short test message to yourself and click Post to Outbox. Listen to the frequency first, and if VARA shows the channel as busy, wait or pick another gateway. When it’s clear, click Start. VARA will call the gateway, and once it connects your message goes out and any waiting mail comes in.

Gotchas

  • Opening the FM session by mistake. Vara FM Winlink and Vara HF Winlink sit right next to each other in the drop-down.
  • Overdriving the audio. Too much drive means a wide, dirty signal and failed connections. Turn the drive down before you turn the power up.
  • Another program holding the COM port. Close WSJT-X, your logger or anything else that talks to the radio before opening the session.

Last Week’s Challenge: Shout-Outs

Last week’s challenge was to pass a Winlink message each way, peer-to-peer, with a friend. Nobody’s posted a completion in the comments yet, so the door’s still open. Grab a club buddy this week and give it a try, then drop both call signs below and I’ll give you a shout-out.

This Week’s Challenge: Work a New State

Make a contact with a state that isn’t in your log yet. Any band, any mode: SSB, CW, FM simplex, or FT8 (tomorrow’s Digital Thursday post will help you get a clean FT8 signal out). Brand new hams, your first state counts!

Done it? Post your call sign and the state you worked in the comments. Everyone who completes the challenge gets a shout-out next Wednesday.

Your Turn

Have you tried Winlink over HF yet? Which band and gateway worked best for you? Tell me in the comments, and ask your own Winlink questions there too. Every Winlink Wednesday post is on the Weekly How-To page.

As an Amazon Associate I earn from qualifying purchases. This site supports local ham clubs.


Discover more from KN4YZY

Subscribe to get the latest posts sent to your email.

Leave a Reply